v
Your current location: Home-> Service and Support->Search result
Product search support
v
TX-NR5009
Product Support
Firmware Update-TX-NR5009 Firmware Update  Time:2018-12-23
User Manual Download-Time:2011-12-19
User Manual
Firmware Update
Software Update
FAQ
News and Notice

Firmware Update             

   

Latest Firmware Number (16 digits): 1081-0700-0210-5103

 As of 10 Jul 2012

  • Improves the operation when HDMI Through is set to on;
  • Stabilizes the operation of Network Control;
  • Corrects the video output when the Picture Mode is set to Through

As of Mar 20, 2012

  • Stabilizes video output when using HDMI/CAT5 Extender on HDMI OUT MAIN terminal

As of 20 December 2011

  • Improves noise during playback of DTS-HD Master Audio with particular Blu-ray disc
  • Corrects operation of Audyssey MultiEQ XT32 in Bi-Amp mode
  • Stabilizes audio output when Zone 2 (or 3) is turned on before the main power

     *This fix is only applied for Pre-Amp models 

As of 31 October 2011

  • Supports Onkyo Remote App for Android version: 1.00;  

           *it is also necessary to update the App. 

Precautions for Firmware Update

  1. Please read the update instructions carefully before beginning. 
  2. The firmware update should take 30 to 40 minutes. Once the update begins, don't turn off the power supply to the A/V receiver until it is time to restart it.
  3. Depending on the conditions of the network, a firmware update via a network may take more than one hour or even fail to finish. If the update is not completed within two hours, turn off the power supply by pushing the ON/STANDBY button and then try updating again from the beginning.
  4. Updating the firmware and adjusting the settings will be done automatically, but may take some time to complete. Please follow the procedures as instructed when you update. Note that the update may fail, or cause problems for your A/V receiver, if you do any of the following:
    • Pull out the A/V receiver’s power cord;
    • Interrupt the power supply to the A/V receiver (e.g. if the breaker is tripped or if there is an electrical outage);
    • Insert or remove the LAN cable from a device in your network when updating over a network;
    • Insert or remove a USB memory device from the A/V receiver when updating via USB;
    • Operate components connected to the A/V receiver via HDMI, such as a TV or a recording device.

    If your A/V receiver is damaged for any of the reasons above, an Onkyo service center will repair the unit for a fee.

     

    As of Mar 20, 2012

    • Stabilizes video output when using HDMI/CAT5 Extender on HDMI OUT MAIN terminal

    As of 20 December 2011

    • Improves noise during playback of DTS-HD Master Audio with particular Blu-ray disc
    • Corrects operation of Audyssey MultiEQ XT32 in Bi-Amp mode
    • Stabilizes audio output when Zone 2 (or 3) is turned on before the main power

       *This fix is only applied for Pre-Amp models 

    As of 31 October 2011

    • Supports Onkyo Remote App for Android version: 1.00;  

               *it is also necessary to update the App. 

    Precautions for Firmware Update

    1. Please read the update instructions carefully before beginning. 
    2. The firmware update should take 30 to 40 minutes. Once the update begins, don't turn off the power supply to the A/V receiver until it is time to restart it.
    3. Depending on the conditions of the network, a firmware update via a network may take more than one hour or even fail to finish. If the update is not completed within two hours, turn off the power supply by pushing the ON/STANDBY button and then try updating again from the beginning.
    4. Updating the firmware and adjusting the settings will be done automatically, but may take some time to complete. Please follow the procedures as instructed when you update. Note that the update may fail, or cause problems for your A/V receiver, if you do any of the following:
      • Pull out the A/V receiver’s power cord;
      • Interrupt the power supply to the A/V receiver (e.g. if the breaker is tripped or if there is an electrical outage);
      • Insert or remove the LAN cable from a device in your network when updating over a network;
      • Insert or remove a USB memory device from the A/V receiver when updating via USB;
      • Operate components connected to the A/V receiver via HDMI, such as a TV or a recording device.

      If your A/V receiver is damaged for any of the reasons above, an Onkyo service center will repair the unit for a fee.

      For detail about Open Source Software, please refer to the link below.

      https://www.onkyo.com/manual/oss/rcv01.pdf

       

      Site Map  |   Contact Us  |   Join Us  |   Terms & Conditions  |   Privacy Policy  |   Delivery and Return Policy  |   Links  
      |  

      © 2015 Pioneer & Onkyo Marketing Asia Ltd. All rights reserved.
      rss
      v